6f6d7d92



13.1. Removal and installation of stupichny assembly of a forward suspension bracket

The divider of spherical support and new nuts of spherical fingers will be required.

Removal

 PERFORMANCE ORDER

1. Dump pressure in hydraulic system (see the Head Uniform hydraulic system).

2. Prop up antiretractable boots back wheels, a front of the car and establish to a poddomkratta it on props. Remove the corresponding forward wheel. Whenever possible, weakening of a nut of fastening of a power shaft has to be made to a car poddomkrachivaniye:
   a) Prop up antiretractable boots forward wheels and take off decorative caps of rims;
   b) Firmly cock the parking brake;
   c) Take a R-shaped clamp and remove a lock cap of a nut;
   d) Weaken a nut by means of a suitable face key.



3. Weaken and partially turn off a nut of a spherical finger of a tip of steering draft on stupichny assembly (turn off a nut until the end of a carving for the purpose of protection of rounds of the last at release of the hinge). Release a sharovy finger of a tip from stupichny assembly by means of a divider of spherical support, then finally remove a nut.

4. Otboltite from a rack also shift a basic arm of an electrical wiring / a hydraulic hose aside.

5. Remove a brake disk (address the Head the Brake system). Weaken and partially turn off a nut of a finger of the lower spherical support (turn off a nut until the end of a carving fingers for the purpose of protection of rounds of the last at release of the hinge). Release a sharovy finger from stupichny assembly by means of a divider of spherical support, then finally remove a nut.
6. Release the external end of a power shaft from stupichny assembly (see the Head Power shafts). Pay attention to the next moments:
   a) There is no need to merge gearbox oil from the transmission;
   b) Do not release an internal pin of a power shaft from transmission, and during the work from the right board of the car do not release also intermediate bearing of a shaft;
   c) A wire tie up the free external end of a power shaft to a suspension bracket element.

7. Give a nut of a coupling bolt of a collar of fastening of stupichny assembly on a suspension bracket rack.

8. By means of a prutkovy key on 8.0 mm part a groove of a collar of fastening of stupichny assembly on suspension brackets (enter a six-sided bar into a groove and turn it on a quarter of a turn). At the same time omit stupichny assembly down, removing it from a rack.

Installation

 PERFORMANCE ORDER

1. Part a collar of fastening of stupichny assembly by means of a prutkovy key (see the previous subsection, the last point).
2. Put on stupichny assembly a suspension bracket rack (the directing ledge on a rack has to get a collar groove).
3. Push a nave up a rack against the stop it in the bearing coat hanger.
4. Establish a coupling bolt (the bolt should be filled in a collar in front), screw a new nut and tighten it with the required effort.
5. Establish into place a brake disk and a support, connect a cable of the drive of the parking brake (address the Head the Brake system).
6. Fill a pin of a power shaft in a nave, screw and tighten a fixing nut (see the Head Power shafts). Whenever possible the nut should be tightened after lowering of the car on the earth.
7. Establish on a suspension bracket rack the bearing electrical wiring arm / a hydraulic hose and fix it by two bolts.
8. Connect a tip of steering thirst to stupichny assembly, having fixed a sharovy finger by a new nut. Tighten a nut of a spherical finger with the required effort.
9. Establish into place a wheel, then lower the car on the earth and tighten wheel (and stupichny) nuts with the required effort.
10. Tighten spuskny the gate of the regulator of pressure and transfer a control lever a suspension bracket to situation "Maximum".
11. In conclusion make adjustment of angles of installation of forward wheels (see the Angles of installation of wheels - the general information, check and adjustment of convergence of forward wheels).