1. Remove a steering wheel (address the Head the Running gear and steering).
2. Remove casings of a steering column (address the Head Kuzov and finishing of salon).

3. Turn out two screws of fastening of the understeering switch.

4. Disunite the contact socket(s) in a back part of the switch and take assembly from a casing.

5. Installation is made upside-down. The description of the procedure of installation of a steering wheel is provided in the Head the Running gear and steering.

1. Remove the central overlay of a steering wheel, at the corresponding complete set remove the safety cushion module (see Removal and installation of components of a safety cushion).

2. Turn out two opened fixing screws and take assembly of switches from a steering wheel.

3. Disconnect an electrical wiring from switches and remove assembly.

4. Installation is made upside-down. The description of the procedure of installation of the module of a safety cushion is provided in the section Removal and installation of components of a safety cushion.

1. Having accurately hooked, release an ashtray from the dashboard, then turn out two fixing screws in the lower part of facing of control panels of functioning of a heater and the radio tape recorder and, hooking the small screw-driver, remove facing.

2. On models with the central arrangement of the radio tape recorder on the dashboard turn out two fixing screws and take assembly of the radio tape recorder from the landing nest, disconnect an electrical wiring and an antenna cable from a back part of assembly.

3. Turn out four screws and take a radio tape recorder casing from the dashboard. In case of need release from clamps on a casing an electrical wiring and an antenna cable.

4. On the models equipped with the central ware shelf in the dashboard turn out four fixing screws and remove the shelf.
5. Through an opening under installation of the radio tape recorder reach clamps of fastening of switches.
6. Release clamps and push out switches from the dashboard (outside).
7. Installation is made upside-down. Track correctness of connection and reliability of fastening of contact sockets of an electrical wiring.

1. Remove casings of a steering column (address the Head Kuzov and finishing of salon).
2. Open a cover of the assembly block of safety locks for the purpose of ensuring access to the lower party of angular finishing section of the dashboard from the driver's party of the car.

3. Turn out the top and lower screws of fastening of angular section, delay finishing on yourself and disconnect from it (or from switches) an electrical wiring. Try to remember adjusting position of contact sockets. Remove finishing section.

4. In a back part of finishing section release clamps of fastening of switches and push out them from the panel outside.
5. Installation is made upside-down. Track correctness of connection and reliability of fastening of contact sockets.

1. Act as it is described in the subsection "The Lower Switches Installed from the Driver's Party of the Dashboard", subitem 1 — 3.
2. Release clamps from the back party of finishing section and push out switches from the panel outside.
3. Installation is made upside-down. Track correctness of connection and reliability of fastening of contact sockets.

1. Release a small ware box / the finishing panel of switches from the central console of the car.

2. Take the panel of switches from the console and disconnect from it an electrical wiring.

3. Push out switches from the panel outside.
4. Installation is made upside-down.

1. Turn out the screw located from below on the rear edge of the panel of facing of the door handle.

2. Having accurately hooked, remove facing of the handle and disconnect the electrical wiring brought to assembly of switches.

3. Take the metal clamp located from the back party of a basic plate and remove assembly of switches.

4. Release clamps and push out switches from assembly outside.

5. Installation is made upside-down. For fastening of a basic plate of assembly of switches use a new metal clamp.

1. Perform the procedures described in the subsection "Switches of Management of Functioning of the Electric Drive of Window Regulators", subitem 1 — 2.
2. Now it is necessary will separate the basic panel of the switch from facing of the internal handle of a door.
3. Two panels are connected by plastic clamps which can be broken off or drilled.
4. After division of basic panels push out the switch from assembly outside.
5. Installation is made upside-down. For fastening of panels use new clamps.

1. Open a door and remove a rubber protective cover from the door switch.
2. Turn out the switch and release it from a rack. Disconnect the electrical wiring brought to the switch and remove assembly from the car.

Glue an electrical wiring an adhesive tape, without allowing it to fail thereby in a rack.

3. Installation is made upside-down. Track reliability of landing on the switch of a protective cover.

1. Open a cover of a ware box, then release a lock uvula in a back part of a cover and completely lower the last.

2. Having hooked, release the switch of illumination of a box and disconnect from it an electrical wiring.

3. Installation is made upside-down.

1. Open a back door, turn out fixing screws, release clamps and remove the panel of an internal upholstery.

2. Turn out screws of fastening of the sensor switch to a door, remove a lock washer.

3. Disconnect an electrical wiring and remove the sensor switch.
4. Installation is made upside-down. Track connection to the grounding wire sensor switch.

1. Remove the central console (address the Head Kuzov and finishing of salon).

2. Having hooked, release the sensor switch from a basic arm in a back part of a control lever of the parking brake, disconnect an electrical wiring.

3. Installation is made upside-down.

1. Having hooked, release a rheostat from the lower casing of a steering column, disconnect an electrical wiring.
2. Connect an electrical wiring and latch a rheostat back in a casing.

1. Remove a steering wheel (address the Head the Running gear and steering).
2. Remove casings of a steering column (address the Head Kuzov and finishing of salon).
3. Walk on an electrical wiring from the switch back and disunite its contact socket.
4. Turn out fixing screws and remove assembly of the switch from a steering column.
5. Installation is made upside-down.